Daylight Saving Time in the U.S. begins earlier and ends later starting this year - which means your PC and/or Phone System might not set its clock correctly when the time comes.
Partner System:
To change the time on your Partner Phone System all you need to do is make sure you are at extension #10 or #11 (must have display)
Then Press Feature 00
Next press the LEFT hand intercom button two (2) times
Next press #101
Enter new Date
After entering new date Press #103 and the enter the new time (in 24 hour format)
Once you have made the changes Press Feature 00 to get out of programming
Legend/Magix System:
To change the time on your Legend/Magix Phone System all you need to do is make sure you are at a main console (Legend MLX 20L or Magix 4424LD+)
Then press System Program
Next press Start on Magix, Exit on Legend
Next press System
Then choose Time/Date
Enter the new time
Next press Enter
Once you have made the changes press Exit to get out of system programming and the phone will return to normal operation
Time Set KX-TDA 50/100/200
Press PROGRAM, STAR, STAR, 1234
(Default password is 1234. yours may have been changed)
Press SP-PHONE
Display shows Date & Time Set
Press ENTER (or Auto Dial/Store)
Display will show year, month and date
Press the button below NEXT on the display
Display will show flashing hour. Enter the 2-digit hour Such as 03 or 11 Enter the 2-digit minute Such as 06 or 44 If needed, set AM or PM Not necessary if correct or change by pressing SEL+
Press ENTER on the Navigator Wheel or the button labeled Auto Dial/Store.
New time is now stored.
Lift handset and hang up to leave programming mode or press exit
Time Set KX-TD 308, 816, 1232, 500 and KX-TA 1232
You must be on the main phone on jack 01 to set time. You can determine if your phone is jack 01 by pressing PROGRAM 99 on a display phone and then pushing the number 6 on the dial pad. The phone will read the jack and extension number. When you have determined the jack 01 phone, do the following:
Example is to change time from to
Press PROGRAM * * 1234
(Default password is 1234. yours may have been changed)
USR-PGM NO >
Press SP-PHONE 3 Times
12 (Hour is flashing)
Enter 2 digit hour
12 (Hour is Flashing)
FWD/DND button or press the softkey below -> on the display
12 (Minute starts flashing)
Enter 2-digit minute 12 (Minute is flashing)
Auto Dial/Store Button New time is stored
Lift handset and hang up to leave programming mode.
Panasonic KX-TA 308/624/824
You must be on the main phone on jack 01 to set time. You can determine if your phone is jack 01 by setting the switch on the end of a display phone to PROGRAM and then pushing the number 6 on the dial pad. The phone will read the jack and extension number. When you have determined the jack 01 phone, do the following.
1.Set switch on end of phone to "PROGRAM" (or push PROGRAM key if you have one)
2.Dial "0"
3.Enter year (last 2 digits)
4.Enter month (01-12)
5.Enter day (01-31)
6.Enter day of week (Sun 0, Mon 1, Tue 2, Wed 3, Thu 4, Fri 5, Sat 6.)
7.Enter Hour (01-12)
8.Enter Minute (00-59)
9.Press 0 for AM 1 for PM
10.Press "AUTO DIAL/STORE" key
11.Return phone switch to "SET" (or push PROGRAM key if you have one)
Adjust the time on the older Panasonic analog telephone system?
KX-T 308
You must be on the main phone, station 11, to set time.
Press Intercom
Dial 77
Enter the hour (01 through 12)
Enter the minute (00 through 59)
Dial 0 for AM or 1 for PM
Press #
Hang up
You must be on the main phone, station 11, to set time.
Press Intercom
Dial 77
Enter the hour (01 through 12)
Enter the minute (00 through 59)
Dial 0 for AM or 1 for PM
Press #
Hang up
KX-T 616
You must be on the main phone, station 11, to set time.
Press Intercom
Dial 77
Enter the hour (01 through 12)
Enter the minute (00 through 59)
Dial 0 for AM or 1 for PM
Press #
Hang up
KX-T 1232
You must be on the main phone on jack 01 to set time. You can determine if your phone is jack 01 by setting the switch on the end of a display phone to PROGRAM and then pushing the number 6 on the dial pad. The phone will read the jack and extension number. When you have determined the jack 01 phone, do the following.
Set switch on end of phone to "PROGRAM"
Dial "0"
Enter year (last 2 digits)
Enter month (01-12)
Enter day (01-31)
Enter day of week: (Sun 0, Mon 1, Tue 2, Wed 3, Thu 4, Fri 5, Sat 6.)
Enter Hour (01-12)
Enter Minute (00-59)
Press 0 for AM 1 for PM
Press "AUTO DIAL/STORE" key
Return phone switch to "SET"
Resetting your ESI phone system’s clock (Installer or Administrator password access required)
The following is derived from the explanation of Function 14 in your ESI phone system’s Installation Manual or Administrator’s Manual (as the case may be).
Current ESI phone systems can be configured to reset the time automatically when Daylight Saving Time (DST) ends or begins each year. However, if your system is not configured that way (or it’s an older ESI phone system that doesn’t perform the automatic time change), the following instructions explain how to reset the time and date manually.
Note:
To configure a compatible ESI system to change time automatically when Daylight Saving Time ends or begins, see “Automatic adjustment for Daylight Saving Time,” below.
On any ESI phone within the system, press PROG/HELP.
Note:
If using an ESI Feature Phone that has separate PROGRAM and HELP keys, press PROGRAM.
The normal station programming menu prompt will begin to play.
Stop the prompt by pressing HOLD (or, on an older ESI phone, PARK).
Enter the Administrator password and then press #. (default password is :456)
Note:
If this doesn’t admit you to Administrator-level programming (the phone display should show ADMINISTRATOR), contact your ESI Reseller for assistance.
Access Function 14 by pressing 1 4. (If the system prompts you to press 1 to set time and date, do so.)
Enter a new time using a twelve-hour format and then press #.
Example:
Enter 1 2 3 3 # for or 3 1 5 # for (note that you need no leading zero for the time).
Select AM or PM by pressing a scroll key and then #.
When the date appears, either:
Press # to accept the currently displayed date as correct; or
Enter a new date in an eight-digit format, including leading zeroes, and then press # and hang up to finish the entry.
Example:
For March 14, 2007, enter 0 3 1 4 2 0 0 7 # (and, to repeat, leading zeroes are required here, unlike in Step 5).
This doesn’t work on ESI phone systems manufactured before February, 2003 — specifically, IP 200, IP 40, IVX 128 Plus, IVX 128, IVX 20 Plus, IVX 20, and [original] IVX. If you don’t know which phone system you have, consult your ESI Reseller.
Microsoft's published a list of products "affected" by the new DST period which includes Windows XP and Outlook. To make sure your Outlook appointments and system clock isn't an hour off starting on March 11, Microsoft's offering a Time Zone Update tool as a free download. Additionally, hit up Microsoft's online wizard to get your XP PC up to speed on the new time change period
**** NOTE**** If you don’t find your system listed here please call us at 718-389-3737 to research your system or for a service call (depending on the system)
